with Purchase of Furnace & Air Conditioner
Cannot be combined with any other offers. Must present coupon at time of service. Not valid on previously completed work.
# Service Summary Responded to service call for running toilet. Upon inspection, identified faulty fill valve and deteriorated flapper causing continuous water flow and leakage. Replaced complete internal tank components including fill valve assembly and flapper mechanism to restore proper function and eliminate water waste.
Responded to service call for a Lennox mini-split condenser unit that was improperly mounted and pulling away from the house siding. Technician reclaimed refrigerant, removed the unit, and properly reinstalled the mounting bracket using longer lag bolts secured to wall studs. After reinstallation, the system was evacuated, charged, and tested for proper operation, resolving the safety hazard and ensuring correct unit function.
Performed preventative maintenance tune-up on 18-year-old LP furnace. Inspected heat exchanger with no compromises found, verified condensate drainage, and tested system operation with 47-degree temperature rise. Identified inducer motor drawing higher than specified amperage (3.4A vs. 2.8A spec) with audible noise; balanced blower wheel and confirmed all other electrical components within specifications. Recommended obtaining estimate for inducer motor replacement.
Replaced 20-year-old Mansfield toilet with new Gerber Viper biscuit two-piece standard round toilet. Installation included new wax ring and bolts. Customer opted for replacement rather than multiple repairs to aging fixture.
Responded to service call regarding malfunctioning toilet handle. Upon assessment, determined toilet required full replacement rather than repair. Presented customer with multiple toilet options, including shorter models as specifically requested for household member with height considerations. Installed new toilet unit and confirmed proper operation before completing service.
Responded to callback regarding shop heater with intermittent fan operation. Diagnosed issue with relay switch that required manual tapping to activate. Replaced defective relay switch to restore proper automatic fan function during heating cycles.
Responded to service call for Hot Dawg shop heater (10-15 years old) that was running but not producing heat. Upon arrival, customer had already performed preliminary cleaning. Diagnostic testing revealed no operational issues after multiple test cycles. System is now functioning properly with adequate heat output.
Responded to no heat call for commercial tube heater system. Upon arrival, found both units operational with temperature at 65°F. Customer had recently brought cold trucks in following a fire call, creating excessive heating load. Replaced thermostat as requested by customer and verified proper system operation. Recommended cleaning reflectors to improve radiant heat efficiency of the tube heater.
Responded to a carbon monoxide emergency where alarms triggered and fire department confirmed CO presence, requiring gas shutoff. Performed comprehensive inspection of furnace including heat exchanger examination, exhaust system check, and combustion analysis with no significant concerns identified. Replaced completely clogged air filter and verified system operation with minimal CO readings (1ppm), likely residual from previous incident.
Provided technical assistance to Mike R for repair of tube heaters. Performed necessary service work to restore functionality on both units that were down. Replacement parts were installed as documented in Meno, requiring two technicians and ladder access for proper installation and commissioning.
Responded to wood boiler system operating issue with zones not shutting off at temperature. Diagnosed wood stove lockout and reset unit to restore operation. Examined pump functionality throughout system and replaced garage pump as troubleshooting measure. Identified design issue causing continuous flow through hot water coil loop even when pump is inactive. Recommended installation of relay-in-a-box (RIB) to allow proper thermostat control of blower and pump to eliminate persistent heat problem.
Responded to no-heat call for one-year-old boiler showing error code. Discovered dead bird obstructing venting and condensate system, requiring disassembly of equipment for removal and thorough flushing. Noted minor dripping from relief valve during operational verification after service was completed.
Responded to no-heat call at fire station regarding non-functional tube heater. Discovered previous contractor had abandoned the repair job, leaving missing parts on one burner and holes in the tubes. System appears to be an older model with significant wear. Coordinated with team member to evaluate replacement options, including pricing for a new unit heater and researching parts availability for the existing system.
Performed comprehensive tuneup on Luxaire gas furnace for new customer. Thoroughly inspected heat exchanger with no defects found, cleaned condensate system and burners, and verified proper operation. Noted outdoor Guardian AC unit requires leveling; customer will schedule AC service in spring when weather permits.
Completed maintenance service on 5-year-old gas furnace. Performed comprehensive tune-up including inspection of heat exchanger, flame sensor cleaning, and condensate system cleaning. Observed corrosion on metal components and examined ductwork connections. Customer reported issues with M30 WiFi thermostat, but opted to continue using current unit after consultation.
Replaced collector box/cold end header box and blower wheel on furnace per approved repair estimate. All components were installed according to manufacturer specifications and system operation was verified to be functioning properly upon completion of work.
AC Repair: I corrected a loud, vibrating AC unit by identifying and securing a loose fan blade that had been causing imbalance. After balancing the fan and inspecting the motor shaft, the system returned to smooth, quiet operation.
Air Purification Installation: I installed a high-efficiency, whole-home air purification system integrated directly into the HVAC ductwork. The unit featured HEPA filtration and UV-C sterilization, significantly reducing airborne allergens, mold spores, and bacteria for healthier indoor air.
Electrical Repairs: Installed a dedicated 240V circuit with upgraded wiring and a new breaker to support high-demand laundry appliances. This installation prevented circuit overload, ensured consistent operation, and improved the safety and capacity of the home's electrical infrastructure.
-
©2026 Hurlburt. All Rights Reserved.
Privacy Policy | Terms and Conditions | Cookie Preferences
Web Design and Internet Marketing by RYNO Strategic Solutions
This site is protected by reCAPTCHA and the Google Privacy Policy and Google Terms of Service apply.