with Purchase of Furnace & Air Conditioner
Cannot be combined with any other offers. Must present coupon at time of service. Not valid on previously completed work.
Furnaces, boilers and heat pumps are the most common heating systems in Elk Mound. We’ll go over the benefits and drawbacks of each option so that you fully understand them. Many homeowners pair a heat pump with a furnace. The heat pump provides cooling during the summer and efficient heating during the winter. When the temperature drops below freezing, the furnace kicks on. Having this reliable form of backup heat ensures you never have to worry about staying warm.
Central AC is an excellent option for homes that prefer consistent comfort and powerful cooling. We’ll perform load calculations to choose the correct size equipment. Undersizing and oversizing both waste energy and increase your cooling costs. They also result in hot and cold spots that make the home uncomfortable. Our accurate sizing process avoids these issues from the start.
If you want the most precise form of cooling, we’ll recommend a zoned setup. You’ll have room-by-room temperature control, which is great for homes with multiple floors. When you need an AC repair in Elk Mound, WI, help is just a phone call away.
Remodeling your kitchen or bathroom? If so, we can do all of the plumbing upgrades. If you’re installing a garbage disposal, we may need to add a dedicated circuit. This helps keep the breaker from tripping when using the new appliance. If you want to update the bathroom with a new toilet, we can install a low-flow model that saves water.
If you’re constantly running out of hot water, it may be time to go tankless. Tankless water heaters not only provide continuous hot water but also use less energy. This means you save money on utility bills. And because they don’t require a storage tank, there’s a lower risk of leaks and flooding.
Our electricians in Elk Mound, WI have extensive training for installing and fixing electrical systems. If you want better airflow in your home, we can install new ceiling fans.
Remodeling often requires adding new switches and outlets. We’ll consider the home’s layout and lighting when choosing where to place them.
We’ll inspect your panel to make sure it has adequate capacity. Upgrades to breakers and wiring are sometimes necessary for safety or performance reasons. You may need a full-panel upgrade to add an EV charger. 100-amp panels don’t have enough capacity to safely support EV charging. By adding a larger panel with ample capacity, you won’t have to worry about overloads.
Many homes near County Road U need sump pumps to manage spring snowmelt and heavy rainfall. Our team installs these devices, including submersible, battery backup, and pedestal types.
Homeowners along Highway 93 often have us install whole-home generators to prepare for storm-related power outages. We’ll connect the transfer switch and set up the wiring so that everything functions reliably.
If you live near Beaver Creek Reserve and want better indoor air quality, we can install a whole-home air purifier. Other solutions for indoor air quality in Elk Mound, WI include whole-home humidifiers and dehumidification systems.
Our customers love our people-driven culture. They frequently leave us 5-star reviews, praising us for our professionalism and reliability. You can read through thousands of them to see why they keep choosing us.
We come to all jobs with fully stocked trucks to fix most problems in one visit. If we ever have to turn off the home’s water or electrical supply, we’ll let you know in advance. Our fast service for emergency HVAC in Elk Mound is greatly appreciated when there are refrigerant leaks or sudden system breakdowns. We’ll arrive quickly to restore comfort with a long-term solution. The Hurlburt Family Rewards Club helps you stay on top of essential maintenance that improves the home’s energy performance and comfort.
Contact Hurlburt today to book service for electric, plumbing, HVAC, and indoor air quality in Elk Mound, WI.
Completed annual air conditioning maintenance and tune-up on residential HVAC system. Performed comprehensive inspection of outdoor condenser unit, noting accumulated dirt and debris on exterior mesh panels typical of normal operation. Evaluated indoor air handler components including filter condition and mechanical connections. All systems tested and operating within normal parameters per manufacturer specifications.
Responded to service call for generator not starting. Performed diagnostic testing on generator control system, which failed multiple tests confirming control failure. Documented electrical panel and circuit breaker configuration with photos. Contacted property owner to discuss repair versus replacement options and will provide pricing for both solutions.
Responded to service call for 40-gallon LP (liquid propane) tanked water heater leaking from the bottom. Inspected unit and identified active leak originating from lower section of tank, indicating potential tank failure or corrosion. Provided on-site estimate for water heater replacement as requested by property owner, who indicated intent to obtain additional quotes before proceeding with repairs.
Responded to multiple copper pipe leaks in residential plumbing system, including critical leak near pressure tank dripping onto electrical components. Conducted comprehensive inspection of all affected areas and documented conditions with photographs. Reviewed all leak locations with homeowner and assessed system condition, noting exposed copper piping in ceiling joists and pressure tank connections requiring attention. Coordinated estimate for complete repipe and new pressure tank tee with accessories to address systemic issues and prevent future failures.
Completed comprehensive air conditioning tune-up on 2-year-old system with no reported issues. Performed full system inspection, cleaned condenser and evaporator components, verified refrigerant levels, tested electrical connections, and conducted operational run test to confirm proper system performance. Demonstrated thermostat away feature to homeowner for optimal energy efficiency during absences.
Completed comprehensive BOGO tune-up on 20-year-old air conditioning and furnace systems. For the AC unit, performed electrical inspection with capacitor testing within specifications, replaced air filter, verified evaporator coil and condensate drain functionality, and identified system operating slightly low on refrigerant charge; homeowner elected to continue operation until replacement is needed. On the furnace, cleaned flame sensor, verified proper gas pressure settings, inspected heat exchanger with no concerns found, and confirmed unit operating correctly with 50-degree temperature rise across the heat exchanger.
Completed installation of CBA38MV air handler with Quantum aluminum coil and variable speed blower motor (2.5 ton capacity), EL22XPV heat pump system, and new thermostat while retaining existing thermostat for in-floor heating system. Installed electric heat kit in air handler per customer request. Verified proper leveling of outdoor heat pump condenser unit and confirmed all electrical connections and control board wiring are secure. Noted tee fitting near pressure tank requires inspection for potential leak and recommended scheduling separate visit for like-for-like electric boiler replacement to avoid mechanical room congestion.
Performed annual inspection on A.O. Smith tanked water heater in preparation for property sale. Conducted comprehensive visual inspection of unit, verifying proper condition of temperature/pressure relief valve, discharge piping, gas line connections, and all copper supply lines. Briefly opened drain valve with attached hose to check for sediment buildup; found no sediment present, indicating proper maintenance history. Inspected all safety labels, electrical connections, and surrounding mechanical systems. Unit found to be in excellent operating condition with no deficiencies noted.
Responded to no cooling condition on geothermal heat pump system. Found failed run capacitor and hard start capacitor with burned wiring connections. Replaced both capacitors, repaired damaged wiring, and performed test run with satisfactory operation. Unit running properly at time of departure, though compressor longevity may be affected by component failures.
Responded to no cooling complaint on 8-year-old residential air conditioning system with reported ice buildup. Upon arrival, confirmed system was low on refrigerant charge. Discussed repair options with homeowner, who elected to proceed with recharging the system. Added refrigerant to manufacturer specifications and injected UV dye into the system for future leak detection if needed. Cycled system through complete cooling operation and verified proper function. All operating parameters returned to normal range. System restored to full cooling capacity.
Responded to a callback for a leaking main water line at the crimp connection. Upon arrival, identified an additional issue with a ball valve leaking near the pressure tank. Replaced the defective ball valve with a new unit, resolving both the dripping condition and ensuring proper system operation. Documented the completed repairs with photos showing the pressure tank assembly and updated copper piping configuration with new valve installation.
Completed preventive maintenance tune-up on one-year-old Lennox air conditioning system. Performed comprehensive inspection with all components operating within manufacturer specifications. Rinsed condenser coil, verified brand new air filter in place, and confirmed proper system performance with 25-degree temperature split across evaporator coil.
Responded to a leak at washing machine hookup connections previously installed approximately seven months prior. Upon inspection, discovered the cold water supply line fitting was loose at the connection point. Disassembled the cold side connection, applied fresh Teflon tape and pipe dope to threads, and properly reassembled the fitting. Tested system for leaks and verified secure, watertight connection. Advised that if leaking recurs, wall-mounted drop ells will require replacement.
Completed Family Rewards cooling maintenance visit on residential air conditioning system. Removed condenser panels and thoroughly cleaned coils, rinsing debris from unit. Inspected all electrical components and tested capacitor, which measured within specification at 35/5 MFD. Verified indoor air filter had been recently replaced. Confirmed evaporator drain line was clear and draining properly. Checked blower settings and confirmed proper configuration. Started system and monitored operation for approximately 15 minutes, verifying 23-degree temperature split across coil. All components operating within normal parameters with no issues identified.
Responded to a water leak at the pressure tank assembly. Upon inspection, identified two leak sources: a faulty pressure switch and a deteriorated ball valve. Replaced the ball valve, pressure switch, pressure gauge, and pressure tank drain valve to restore system integrity and prevent further water damage.
Responded to kitchen sink leak caused by improper supply line adapter installation. Removed faulty connections and installed two new compression straight stops to provide proper shut-off capability where none previously existed. Tested all connections and verified system is leak-free and functioning properly.
Completed comprehensive preventive maintenance on both furnace and air conditioning systems. Performed furnace inspection including cleaning of routine components, motor inspection, heat exchanger evaluation, and operational verification with all systems functioning properly. Conducted air conditioning maintenance including condenser coil cleaning, electrical component inspection, refrigerant charge verification with 19-degree temperature differential within specifications, drain line clearing, and installation of customer-supplied air filter. All equipment operating as designed with no deficiencies noted.
Responded to no heat call on 20-year-old furnace experiencing intermittent failure to ignite. Unit was running through cycle but shutting down without firing, displaying same fault code as previous service call earlier in the year. Upon diagnostic testing, discovered no 24-volt signal present to or through the pressure switch circuit during initial troubleshooting. Performed comprehensive system testing and attempted to replicate the failure condition by cycling unit multiple times and forcing potential trip scenarios. Issue did not recur during extended testing period, suggesting intermittent electrical fault in low-voltage control circuit or pressure switch assembly. Given age of equipment and history of recurring intermittent failures, recommended monitoring system closely and considering replacement due to reliability concerns with 20-year-old components.
Reinstalled complete plumbing assembly underneath double-basin kitchen sink following previous removal. Reconnected water supply lines and drain system, including P-trap configuration, white PVC drain lines, and garbage disposal unit with associated discharge piping. Verified all connections secure, tested system for proper drainage and confirmed no leaks present.
Responded to furnace exhaust pipe leak in utility space. Upon inspection, identified failed 2-inch PVC elbow fitting on vent pipe system causing water dripping from condensate line leading outside. Removed defective elbow, installed new 2-inch PVC elbow with proper primer and cement application, and verified all connections were secure. Ran furnace for approximately 10 minutes to test system under normal operating conditions and confirmed leak was eliminated with no further dripping observed.
©2026 Hurlburt. All Rights Reserved.
Privacy Policy | Terms and Conditions | [cookie_preferences_link]
This site is protected by reCAPTCHA and the Google Privacy Policy and Google Terms of Service apply.