with Purchase of Furnace & AC
Includes Merv 16 5" media cabinent and ApcoX Premium UV-light. Cannot be combined with any other offers. Must present coupon at time of service. Not valid on previously completed work.
Our plumbing and heating repair services are designed to keep your home’s systems functioning properly all year long. Read our reviews below to see what your neighbors are saying about our plumber and heating repair services in Houlton, WI.
Completed sold repair on jetted soaking tub by replacing a T assembly with a broken flange nut. Installed all necessary pipe and fittings to repair the leak, allowed the assembly to set up for 25 minutes, then tested the system by running the jets for 10 minutes with no leaks detected. Work includes a 1-year parts and labor warranty.
Completed comprehensive tune-up maintenance on both furnace and air conditioning systems. Inspected furnace components including filter, blower assembly, and flame sensor—all found to be clean and in good condition. Verified condensate drainage system functioning properly. Identified minor leak at collector box seal and provided estimate for future repair. Tested gas pressure and confirmed proper settings. System startup demonstrated proper operation with 50° temperature rise across heat exchanger. Proceeded to air conditioning unit and performed electrical component inspection. Tested capacitor reading 45/5 microfarads—within specification. Rinsed outdoor coil, which was already in excellent clean condition. Started system and verified proper operation with 23° temperature split across evaporator coil. All electrical connections secure and refrigerant charge adequate based on operational parameters. Advised monitoring collector box leak for future service needs. Both systems operatin
# HVAC Service Report Responded to recurrent pressure loss issue in residential boiler system. Upon arrival, performed comprehensive inspection of NTI boiler unit and associated hydronic components including expansion tank, water heater, and filtration systems. This marked a follow-up visit for ongoing pressure loss concerns that were previously addressed approximately one month prior. Conducted thorough pressure testing and visual inspection of all accessible piping connections, valves, and fittings throughout the boiler system. Examined copper piping runs, PVC venting, and interconnected plumbing components for signs of leakage or deterioration. Inspected the blue expansion tank for proper pre-charge pressure and functionality. Evaluated all mechanical connections at the boiler manifold and distribution lines. Documented current system conditions with photographic evidence showing the complete mechanical room layout and equipment configuration. Previous service history was reviewe
Responded to a leaking jetted tub caused by a cracked union nut on the circulation pump. Diagnosed the issue, documented the damaged component with photographs, and completed a part order form for the necessary replacement union nut to provide pricing and prepare a repair estimate for the customer.
Responded to kitchen sink backup with water leaking from the studor vent. Upon inspection, determined the studor vent was installed below the flood level rim, creating a code violation and leak point when the drain backed up. Diagnosed the drain blockage as likely caused by food debris and grease accumulation in the line. Cabled the kitchen sink drain line to clear the obstruction, removing food debris during the process. Restored proper drainage flow and reassembled all drain components. Performed extended water flow testing to verify complete blockage removal with no backup or leakage observed. Modified the studor vent installation by cutting and extending the vent pipe to position it above the flood level rim, preventing future leakage in the event of drain backup. Conducted final testing of the complete drainage system to confirm proper operation and code-compliant installation. All components functioning correctly upon completion.
Responded to no hot water call at property with new homeowners unfamiliar with the heating system. Upon arrival, found boiler displaying ER4 error code indicating low water condition—the second occurrence within two months. Added water to the boiler system, which restored proper operation and unit fired successfully. Advised customer that if low water condition recurs, a pressure test of the radiant floor heating system will be necessary to identify potential slow leaks in the hydronic loop.
Completed comprehensive duct cleaning service on residential HVAC system, accessing 20 total supply and return duct openings throughout the property. Removed significant accumulation of pet hair, dust, and debris from ductwork using professional vacuum equipment brought in through rear entrance. Cleaned and reinstalled all accessible vent registers and grilles, noting some duct sections were inaccessible and did not require opening.
Responded to service call for continuously running humidifier. Diagnosed improper wiring where low voltage was connected directly to outlet instead of furnace control board. Rewired humidifier to integrate with heating system so unit now operates correctly only when heat is called for. Noted suboptimal humidifier ductwork installation that may need attention in future service.
Responded to service call for boiler malfunction resulting in no hot water; diagnosed pressure switch code error. Upon removing the cover, system became operational, but identified failing bearing in combustion fan motor causing abnormal noise. Submitted parts request for replacement fan motor as current unit appears to have temporarily locked up but is functioning inconsistently.
Performed inspection of electric boiler system for in-floor heating in basement. System diagnostic revealed absence of glycol protection. Verified proper operation of all heating elements and overall boiler functionality. Prepared estimate for glycol addition and emailed to customer for review.
Responded to service call for water heater with pilot light ignition failure. Upon inspection, found deteriorated copper pipes with significant oxidation and damaged insulation near the water heater installation. Diagnosed issues with both the water heater and pressure tank, determining both require replacement due to age-related deterioration and performance problems.
Responded to callback for no heat issue on Rinnai boiler. Diagnosed error code ER4 indicating open stack limit switch. Discovered corroded wiring connection at stack limit switch that was previously identified for replacement but not completed during prior service visit. Temporary repair attempted with limited success. Ordered replacement part to arrive Monday and scheduled urgent follow-up installation before homeowner closing.
Performed diagnostics on NTI boiler system after customer reported no hot water. Identified malfunctioning safety switches as the root cause preventing proper heating operation. Replaced defective safety switches, restoring hot water functionality. System now operating within normal parameters.
AC Repair: I resolved a frequent short cycling issue caused by low refrigerant levels. After confirming the leak source at a service valve, I repaired it, evacuated the system, and recharged it to the manufacturer’s specifications, restoring steady, even cooling.
Generator Installation: I installed a whole-home standby generator, coordinated with utility company requirements, and connected it to the electrical panel via an automatic transfer switch. This ensured seamless backup power during outages and peace of mind for the homeowner.
Summertime Air Conditioning System Tune-Up: Conducted a thorough seasonal tune-up on a residential AC system, which included cleaning the evaporator and condenser coils, verifying refrigerant pressure, lubricating moving parts, and calibrating the thermostat. The tune-up improved system response and prolonged unit lifespan.
Plumbing Repairs: Replaced a failing water pressure regulator that was causing fluctuating water pressure throughout the home. After installing a new, adjustable regulator, we calibrated it to the ideal PSI, ensuring stable and consistent water flow that protects fixtures and appliances.
50 GALLON ELECTRIC WATER HEATER INSTALLED IN PLACE OF LIKE UNIT. TO INCLUDE DRAINING AND REMOVAL OF OLD UNIT AND BASIC INSTALLATION MATERIALS, AS WELL AS REPLACEMENT OR ADDING EXPANSION TANK
Furnace Repair Service: A homeowner reported their heating system was short-cycling. After diagnosing the issue, I found low refrigerant levels affecting efficiency. I carefully replenished the refrigerant, restoring steady operation and ensuring the home remained warm and comfortable throughout the winter.
Furnace Replacement Service: Replacing an outdated furnace, we introduced advanced components, including a high-efficiency burner and improved insulation. This solution ensures energy savings and consistent home heating.
©2026 Hurlburt. All Rights Reserved.
Privacy Policy | Terms and
Conditions | [cookie_preferences_link]
This site is protected by reCAPTCHA and the Google Privacy Policy and Google Terms of Service apply.