Plumbing, Electrical, and HVAC company in Plymouth, MN
We’ve assisted homeowners for over 65 years and will proudly service your home as well.
Highly Rated
Satisfaction Guaranteed
0% Financing
Friendly Technicians
A split-level near Medicine Lake can give us a very different set of comfort problems from a larger western Plymouth home with multi-stage equipment and multiple zones. Much of the city grew during the 1970s through 1990s, so aging ductwork and mechanical systems are now a regular part of the service picture across the West Metro. Hurlburt Heating, AC, Plumbing, & Electrical provides heating, cooling, plumbing, electrical, and indoor air quality service throughout Plymouth. Call [site_info_phone_number] or connect online to schedule service.
Whether you’re dealing with sparking outlets or a leaky faucet, make Hurlburt your first call. We’ll get your house back to normal fast!
Plymouth Homes Reflect Several Decades of West Metro Growth
Plymouth’s late-20th-century building boom left the city with a large number of split-level and multi-level homes that now have 30- to 50-year-old duct systems and equipment that may already have been replaced once. Western neighborhoods in the Wayzata Schools catchment include larger executive properties that can use high-capacity, multi-stage systems, while older homes around Medicine Lake may have boilers, radiant heat, or different cooling arrangements.
The housing changes again around Hamel and Old Hamel, where the northwest part of Plymouth retains a more rural identity. French Regional Park on Medicine Lake, Parkers Lake, Millennium Garden, the Hilde Performance Center, and the Luce Line Trail are familiar markers across a city that has expanded through several distinct residential areas. Plymouth also has a sizable townhome and condo footprint, along with strict municipal permitting that applies when mechanical systems are replaced.
Air Conditioning Services in Plymouth, MN
Humid summer weather can expose airflow problems quickly in Plymouth’s split-level and multi-level homes. Upper floors may stay warmer when older ducts are undersized, poorly balanced, or simply showing their age after several decades of use. Spring tree and grass pollen also increases filtration concerns before the cooling season reaches its peak, especially as outdoor activity picks up around East Medicine Lake Park and the Luce Line Trail. Central split systems remain the standard cooling setup across much of the city.
Air conditioning and indoor air quality services include:
Air conditioning replacement
Air conditioning repair
Air conditioning maintenance
Ductless systems
Indoor air quality services
Larger custom homes in the western Wayzata Schools area may use higher-capacity or multi-stage equipment, while older lakeside properties can have boiler or radiant heat paired with a different cooling arrangement. Aging ductwork is also driving demand for duct sealing, air purification, and humidity control throughout Plymouth. When one level of the home stays warmer, replacing the outdoor unit alone may not solve the problem. We need to know how air is moving through the existing ducts before deciding what needs attention.
Electrical services include:
Electrical repair services
Electrical installation and wiring
Whole-home generators
Switches, outlets, and ceiling fans
Panel replacement and repair
EV chargers
Smart home installations
An established home near Parkers Lake may have gone through several rounds of equipment upgrades since it was built, while newer western properties may start with more modern infrastructure. Townhome and condo communities add compact installation spaces and HOA requirements that can affect how projects are approached. Plymouth’s strong interest in high-efficiency equipment and modern controls means electrical work often needs to account for what has already been added to the house. The panel and wiring have to be evaluated as part of that bigger picture.
Heating Services in Plymouth, MN
Plymouth winters can push heating equipment hard for months at a time. Severe sub-zero cold creates immediate furnace concerns, while the first autumn startup can produce the familiar burning-dust smell that sends homeowners checking whether the system is operating normally. Forced-air natural gas furnaces are the standard residential setup across much of the city, but older properties around Medicine Lake and custom estates can include boilers or in-floor radiant heat. The winter conditions familiar around places such as Plymouth Ice Center can arrive quickly once fall gives way to sustained cold.
Heating services include:
Heating installation
Heating replacement
Heating repair
Heating maintenance
Heat pumps
Furnaces
Boilers
Geothermal
Plymouth weather is also known for rapid reversals. A March “false spring” can be followed by another late-season blizzard, while May and September can move quickly between heating and cooling. High-efficiency systems and heat pumps are gaining interest in the market, supported by the Xcel Energy and CenterPoint Energy rebate opportunities. A larger home in western Plymouth may call for multi-stage equipment, while a lakeside property can have a hydronic setup that needs a completely different service plan.
Plumbing Services in Plymouth, MN
Plumbing work in Plymouth often takes place in homes where the mechanical equipment has changed several times since the original construction. A water heater may have been replaced years after the furnace, while boilers, radiant systems, and newer HVAC equipment may share utility space in older properties. Larger custom homes can have more extensive plumbing layouts, while townhomes and condos tend to have compact equipment configurations. That variation is common across a city that grew heavily during the 1970s, 1980s, and 1990s.
Plumbing services include:
Plumbing repair
Plumbing installation
Leak detection and repair
Sewer and drain service
Water heaters
Sump pumps
Water treatment
Gas lines
Older homes around Medicine Lake and established neighborhoods near central Plymouth may also have several generations of mechanical equipment sharing the same utility area. That makes available space and existing connections important when a water heater, gas line, or other plumbing component needs work. Homes farther west or in managed communities can present a different layout, but the first step is still understanding what is already installed.
Your Friendly Plymouth Neighborhood Team
Plymouth is one of the largest cities in Minnesota. The good news is this means you can always find something to do. For example, if we’re repairing your plumbing, you can take a nature walk at Clifton E. French Regional Park. Or, if we’re installing a new AC, you can go enjoy craft beer
at Luce Line Brewing. Prefer to do something educational? Check out the Plymouth Historical Museum while we take care of your heater.
Neighborhoods We Serve in Plymouth Include:
Southwest Plymouth
Southern Plymouth
Parkers Lake
Medicine Lake / French Park
Top-Notch Home Services Company in Plymouth
Choose Hurlburt whenever you need electrical, plumbing, heating and cooling services. Our team of more than 60 professionals includes professional plumbers and electricians. We also have 65+ years of industry experience, and all installations include a 12-month warranty. We provide high-quality work, and we always put people first.
Are you looking for an electrical, plumbing, or HVAC company in Plymouth? Reach out to our team of experts today!
Recent Jobs and Reviews in Plymouth, MN
Plymouth, MN at a glance
Hurlburt Heating & Plumbing has completed 20 jobs in Plymouth, MN in September 2026.
The most recent job was on September 25, 2026.
Hurlburt Heating & Plumbing has completed 184 jobs in Plymouth, MN in the last 12 months. The first job there was in October 2025.
Job Locations and Reviews
Joe V.Checked in
Responded to service call for water heater replacement estimate. Upon inspection, found existing Rheem Rheemglas Fury water heater experiencing flame rollout condition, indicating a dangerous combustion issue. Unit was determined to be very old and beyond safe operational lifespan. Documented current installation with photographs showing water heater location in basement utility area, existing venting configuration with metallic ductwork, surrounding plumbing connections including copper piping, and overall mechanical room layout. Assessed installation requirements for new water heater replacement, including proper venting, gas line connections, and code compliance needs. Provided comprehensive estimate for complete water heater replacement due to safety hazard posed by flame rollout condition on aging unit.
Plymouth, MN 55447
Alton S.Checked in
Completed scheduled heating maintenance agreement on dual furnace system. Performed comprehensive tune-up on both units including cleaning flame sensors and burners, inspecting heat exchangers for cracks with no issues found, and verifying blower motor and inducer motor wiring integrity. Conducted carbon monoxide testing with readings at 50-60 ppm, confirming safe operational levels. Verified all three zone motors functioning properly and inspected air filtration. Replaced humidifier filter on both systems and identified minor crack in one humidifier feed tube, which property owner will address independently. All systems tested and confirmed operational and winter-ready.
Plymouth, MN 55447
Alton S.Checked in
Responded to no-heat call on recently installed Lennox furnace displaying C2 error code. Diagnosed miswired W2 thermostat connection at control module; relocated W2 wire to proper terminal and added jumper wire from module W2 to furnace control board W2, restoring second-stage heating operation. Upon testing, identified inadequate gas supply pressure measuring 3.47" W.C. during operation and 6.50" W.C. at rest, dropping to 2.12" W.C. under load, with manifold pressure reading 2.67" W.C. despite adjustment attempts. Determined external gas regulator unable to maintain proper supply pressure under demand, indicating upstream gas supply issue requiring utility company attention. Advised property owner that while furnace wiring has been corrected and unit now operates properly, low incoming gas pressure from main line will affect heating performance and should be addressed by gas utility provider.
Plymouth, MN 55447
Moe R.Checked in
Performed comprehensive maintenance inspection on 30-year-old Lennox air conditioning system. Tested and verified contactor, capacitor, and amp draws all within normal operating parameters. Confirmed refrigerant charge at proper levels. Cleaned outdoor coil and inspected air filter, blower wheel, evaporator coil, and control board—all found in clean condition and functioning properly. Measured temperature drop across system at 20 degrees, confirming unit is operating within manufacturer specifications. System is performing efficiently with no deficiencies noted or repairs required at this time.
Plymouth, MN 55447
Jarrod S.Checked in
Responded to report of water leak originating from bathroom shower area with visible water damage extending to kitchen below. Conducted thorough inspection of bathroom fixtures, including shower enclosure, toilet, and drain systems to identify source of moisture intrusion. Accessed crawl space to examine plumbing infrastructure and document water staining patterns beneath bathroom floor. Inspected shower tile installation, grout lines, and caulking for potential failure points allowing water penetration behind wall assembly. Photographically documented conditions of plumbing fixtures, tiled surfaces, and affected structural areas for insurance claim submission. Determined leak to be phantom-type requiring further investigation of shower pan integrity, drain seal, or grout deterioration as probable causes.
Plymouth, MN 55441
Eric V.Checked in
Performed comprehensive maintenance on a 7-year-old furnace system. Upon arrival, system was inoperative and displaying E2 error code indicating open low pressure switch. Diagnosed water accumulation in inducer motor causing operational failure. Drained inducer motor and discovered blockage in condensate drain line. Cleared blockage and thoroughly flushed drain system to restore proper drainage. Conducted full system inspection including thermostat operation, air filter condition, blower motor function, inducer motor operation, capacitor performance, and electrical wiring connections—all components found satisfactory. Verified temperature split across heat exchanger within acceptable range. Inspected heat exchanger for cracks or deterioration, tested igniter operation, cleaned flame sensor, and measured gas pressure—all parameters within manufacturer specifications. System restored to normal operation with all safety controls functioning properly.
Plymouth, MN 55447
Roger M.Checked in
Completed fall maintenance tune-up on residential furnace system including inspection of humidifier, filter replacement, and drain tube service. During initial diagnostics, discovered elevated carbon monoxide levels traced to a failing draft inducer motor. Due to the age of the existing unit and cost-effectiveness of replacement versus repair, proceeded with full furnace system replacement rather than inducer component repair alone.
Plymouth, MN 55441
Tony C.Checked in
Responded to service call for outdoor faucet experiencing seasonal leaking and two indoor faucets with suspected cartridge failures. Replaced outdoor spigot assembly mounted on exterior wall, including installation of new brass valve body with cross-handle and connection to existing flexible braided supply line via adapter fittings. Addressed water intrusion issues affecting the mounting area on white wooden trim. Inspected and serviced interior plumbing connections in utility access area, working with PVC supply lines and flexible braided hoses connected to wooden platform assembly. All connections tested for proper operation and leak-free performance upon completion.
Plymouth, MN 55447
Jared R.Checked in
Responded to no hot water complaint and found boiler controller board failed with blank display screen preventing system operation. Replaced defective V-15 control board and performed complete system reset. Programmed all heating zones and domestic hot water settings, then cycled system to verify proper operation. Adjusted and set gas pressures and combustion parameters to manufacturer specifications. Purged air from all heating zones and verified auto-fill operation and settings. Secured loose wiring and thermostat wires that were left hanging from previous remodeling work. Identified damaged air relief valve caused by prior system freeze event and ordered replacement cartridge for future installation. System restored to normal operation with all zones functioning properly.
Plymouth, MN 55441
Matt M.Checked in
Responded to service call regarding outdoor frost-free spigot that was difficult to operate and water pressure concerns. Upon inspection, confirmed that the city had already addressed and corrected the water pressure issue. Evaluated the Mansfield frost-free hose bib and determined the internal components required rebuilding due to operational difficulty with the shutoff mechanism. Performed complete rebuild of the Mansfield frost-free spigot, replacing worn internal valve components to restore proper function and ensure smooth operation of the shutoff handle.
Plymouth, MN 55447
Jared R.Checked in
Responded to service call for boiler system with no hot water and failed display. Upon arrival, diagnosed failed control board preventing system operation. Unable to complete scheduled maintenance tune-up due to non-operational control board. Ordered replacement control board for hydronic heating system. Documented existing installation including expansion tank, circulator pump, copper piping network with brass fittings, and stainless steel storage tank. System currently inoperable pending replacement board installation to restore hot water functionality and complete annual maintenance tune-up.
Plymouth, MN 55441
Eric V.Checked in
Completed comprehensive maintenance inspection on 3-year-old furnace and air conditioning system. Inspected and verified proper operation of furnace components including air filter, temperature split, burners, flame sensor, igniter, blower motor, capacitor, condensate drain, and heat exchanger with all components functioning within normal parameters. Performed AC maintenance including inspection of thermostat, temperature split, outdoor condenser unit, evaporator and condenser coils, motors, capacitors, compressor, and condensate drain system. Verified 410A refrigerant charge and pressures at 61-degree ambient temperature. Measured electrical performance including voltage and amperage readings on system components. Both heating and cooling systems operating normally with no deficiencies noted at time of service.
Plymouth, MN 55441
Roger M.Checked in
Completed annual heating maintenance visit including comprehensive tune-up of one furnace and one humidifier system. Replaced humidifier pad as part of scheduled maintenance. Performed diagnostic testing using clamp meter to verify electrical parameters and system performance, confirming all readings within normal operating ranges. All equipment inspected and found to be functioning properly with no issues identified.
Plymouth, MN 55446
Roger M.Checked in
Performed scheduled furnace tune-up on system originally installed in 2012. Upon inspection, found dirty air filter and identified failing blower motor producing intermittent humming noise during operation. Replaced defective blower motor to restore proper airflow and eliminate noise issue, ensuring system operates efficiently for continued heating performance.
Plymouth, MN 55442
Eric V.Checked in
Completed comprehensive heating maintenance on Lennox furnace system. Performed thorough inspection of thermostat, indoor air handler, filter, drain line, blower motor, inducer motor, capacitor, and electrical wiring with all components found in proper working condition. Evaluated temperature split across system, inspected heat exchanger for cracks or deterioration, tested igniter and flame sensor operation, and verified gas pressure within manufacturer specifications. Conducted fireplace maintenance including inspection of pilot assembly, glass, log set, embers, electrical wiring, gas valve, and draft operation. All fireplace components found functioning properly. Combustion analyzer was unavailable during this visit to perform complete safety analysis and CO level testing. Completed follow-up form to schedule return visit for combustion safety check and carbon monoxide level verification. System operating normally at time of service completion.
Plymouth, MN 55442
Fred G.Checked in
Responded to service call for excessive noise from Fantech HRV unit attached to furnace system, with customer reporting inadequate exhaust ventilation and related respiratory irritation symptoms. Upon inspection, identified faulty blower motor as noise source and temporarily unplugged unit to eliminate immediate health concerns. Recommended HRV blower motor replacement to restore proper ventilation and provided enhanced warranty coverage option, then performed preventative maintenance tune-up on 4-year-old furnace system while on site.
Plymouth, MN 55441
Roger M.Checked in
Responded to no cooling complaint with water pooling around furnace area. Found clogged condensate drain line causing water to back up and leak onto basement floor near HVAC equipment. Cleared obstruction from drain line, restored proper drainage flow, and verified system operation. Unit returned to normal cooling function with no further leakage observed.
Plymouth, MN 55447
Matt M.Checked in
Replaced house side valve and indoor shut-off valve for exterior faucet. Both the house side valve and spigot valve were successfully replaced and tested for proper operation. Work completed in basement utility area with copper piping connections properly secured.
Plymouth, MN 55447
Cassandra M.Checked in
Conducted comprehensive water heater replacement estimate for residential property. Evaluated existing A.O. Smith water heater installation, assessed current copper supply line connections with red-handled ball valves, examined PVC drainage piping configuration, and documented HVAC ductwork proximity to water heater location. Photographed existing installation including all plumbing connections, shutoff valves, and mechanical room layout to provide accurate replacement proposal and ensure proper sizing specifications for new unit installation.
Plymouth, MN 55447
Fred G.Checked in
Completed annual heating maintenance visit on two units: gas furnace and gas fireplace. During inspection, discovered critical safety issues with the furnace including severely rusted heat exchanger, deteriorating burner assembly, overheating inducer motor, and low capacitor readings. Documented interior heat exchanger corrosion via camera inspection showing extensive rust buildup throughout the chamber. Replaced filter and recommended immediate furnace replacement due to compromised heat exchanger integrity posing potential carbon monoxide hazard.
“Mark was very pleasant to work with! He was on time and took care of my plumbing needs efficiently and effectively. I would definitely use him again for any plumbing issues I may have. I have been using Hurlburt for all of my heating, plumbing, and electrical needs and have always been satisfied!”
Alison A.
“Great service! Professionals starting from the first person I spoke to on the phone and finalizing with the person who finished the installation and cleaned up after. Staff explained everything well. Highly recommended!!!”
Jessica F.
"Outstanding service as always! Hurlburt goes above and beyond for their customers. We got scheduled right away, and Shawn did a great job. I will continue to use these guys for everything!!!"
Nicole T.
"Our technician Mike was just awesome. Took the time to show me what he was doing and explained why he was doing it. Gave me an honest evaluation of my situation. You can’t go wrong with Hurlburt and the work ethics of the employees."
Jean C.
Trevor came to service our AC unit. Very happy with his work. Trevor was friendly and knowledgeable, and got our issue fixed quickly. Hurlburt Heating and Plumbing is a great company to work with."
Debbie L.
"Hurlburt has helped us out with both plumbing and HVAC services in the past and have always done a great job. All their technicians, especially Mark, have been kind, professional, and quick with service!"