
To get assistance with your HVAC and plumbing repairs, maintenance, and installations, look no further! To see what our satisfied customers think about our HVAC and plumber services in Prescott, WI, read our reviews below.
Hurlburt Heating & Plumbing has completed 20 jobs in Prescott, WI between August 2026 and September 2026.
The most recent job was on September 30, 2026.
Hurlburt Heating & Plumbing has completed 121 jobs in Prescott, WI in the last 12 months. The first job there was in July 2017.
Performed inspection of 8-year-old tanked water heater in response to venting concerns. Upon examination, identified improper venting configuration with back-pitched vent pipe, which violates code requirements and creates potential for condensate accumulation and exhaust gas spillage. Documented existing conditions with photographs showing water heater installation alongside HVAC system in basement mechanical room. Verified water heater connections including gas supply lines with red valve handles and blue water connections at base of unit. Assessed overall system condition and surrounding mechanical equipment including furnace with white PVC intake/exhaust vents and metal ductwork. Provided estimates for new water heater replacement to address venting deficiencies and ensure proper code-compliant installation.
Responded to gas leak call on exterior gas line damaged by landscaping contractor. Upon arrival, performed leak detection test and visual inspection of gas piping on east side of residence. Located damage to gas line where landscaping equipment had nicked the pipe, compromising the metallic shield with a cut exceeding half an inch in length. The damage penetrated through multiple layers, exposing the bottom layer of the gas pipe structure. Documented damage with measurements and photographs showing extent of deterioration to protective coating and metallic shielding. Determined that the affected section requires removal and splicing to restore system integrity and safety. Advised homeowner that damaged pipe section must be cut out and replaced with proper gas line splicing procedures to meet code requirements. Collected diagnostic information and provided recommendations for repair scope. Follow-up pricing for gas line repair to be provided to homeowner.
Responded to urgent service call for sewer pump replacement following recent septic tank drainage. Removed existing failed pump from concrete access pit and installed customer-supplied replacement unit. Completed PVC discharge connection modifications to accommodate new pump configuration. Upon completion of installation, customer planned to fill tank and perform operational testing to verify proper pump function and discharge flow.
Responded to service call for kitchen sink and dishwasher drainage issue. Upon arrival, found double-basin kitchen sink experiencing backup with dishwasher failing to drain properly. Performed diagnostic assessment of drainage system and identified blockage affecting both fixtures. Cleared obstruction from drain line, restoring proper flow and drainage function. Verified dishwasher now draining correctly with no standing water remaining in unit. Conducted water softener inspection as part of scheduled maintenance check. Tested all affected fixtures to confirm complete resolution of drainage problem and proper operation of plumbing system.
Responded to report of water leakage in basement originating from furnace area near water heater and dripping from filter location. Upon arrival, inspected condensing unit and A-coil assembly for drainage issues. Confirmed A-coil drain line was flowing properly with no blockages detected. Connected refrigerant manifold gauges to assess system performance and identified low refrigerant charge as primary issue affecting cooling capacity. Low refrigerant levels were causing inadequate dehumidification, resulting in excess moisture and water accumulation in basement area. Evaporator coil showed signs of dust and dirt buildup on fins, which can restrict airflow and contribute to condensation problems. Provided assessment and quote for refrigerant recharge to restore system to proper operating pressures and temperatures. Discussed long-term options including potential system replacement. Recommended monitoring system performance following refrigerant addition to ensure adequate cooling and p
Conducted comprehensive plumbing inspection of residential property built in 2007. Inspected toilet tank flush mechanism and fill valve components, noting mineral deposits and sediment buildup in tank, and evaluated bathroom shower/tub plumbing fixtures and diverter valve operation to ensure proper functionality.
Responded to kitchen sink drain leak and clog beneath the trap assembly. Snaked the drain line to clear blockage, then disassembled and rebuilt the drain trap system with new PVC components to eliminate the leak. Tested system for proper drainage and verified all connections were secure with no active leaks upon completion.
Completed routine fall maintenance tune-up on 8-year-old furnace under maintenance agreement. Performed comprehensive inspection including cleaning flame sensor, verifying proper condensate drainage, checking air filter condition, inspecting blower wheel, and testing all electrical components. During heat exchanger inspection, identified several rivets showing abnormal appearance compared to surrounding rivets; documented findings with photographs for warranty consideration. System operational testing confirmed proper startup sequence and 50-degree temperature rise across heat exchanger, indicating adequate heating performance despite identified concerns requiring future attention.
Completed installation of customer-supplied bidet attachment to existing toilet fixture and replaced three toilet shutoff valves throughout the residence. All shutoff valves were upgraded from old-style, hard-to-operate models to new quarter-turn ball valves for improved accessibility and ease of use. Bidet installation included proper connection to water supply line, verification of secure mounting, and testing for leaks and proper operation.
Responded to no heat call on 10-year-old furnace with intermittent heating issues. Upon diagnostic inspection, found multiple critical component failures including failing flame sensor and ignitor, inducer draft motor drawing high amperage, and suspected exhaust leak in secondary heat exchanger that could not be fully confirmed due to access limitations. Unit was operational at time of arrival but exhibited unreliable performance. Due to age of equipment and extent of multiple simultaneous failures requiring costly repairs, recommended full system replacement. Documented conditions with photos and scheduled replacement estimate appointment.
Responded to report of white crystalline substance accumulating on sewage pump discharge piping. Upon inspection, identified improper seal at check valve due to misaligned discharge pipe and deteriorated fernco coupling. Removed defective fernco connector and straightened crooked discharge pipe section to ensure proper alignment with check valve. Installed new fernco coupling and reconstructed affected piping segment to establish secure, leak-free connection. Verified system operation and confirmed elimination of salt-like residue buildup on exterior of discharge line.
Responded to HVAC install callback for damaged ductwork insulation in basement mechanical room. Upon inspection, found existing duct felt liner torn and compromised at multiple corners with several holes present. Removed deteriorated felt material from rectangular metal supply duct and replaced with new insulation liner, ensuring proper sealing at all seams and corners to restore system efficiency and prevent air leakage.
Responded to service call for IBC hot water boiler displaying low water pressure code and auto-fill malfunction. Upon arrival, confirmed system was experiencing low pressure and automatic fill valve was not functioning properly. Inspected and adjusted auto-fill valve to restore proper operation. Performed comprehensive annual maintenance service on the boiler system. Disassembled and removed heat exchanger for thorough cleaning to remove scale buildup and ensure optimal heat transfer efficiency. Cleaned burner assembly and combustion chamber. Reassembled heat exchanger and verified all connections were properly secured. Conducted full electrical system inspection, checking all control components, safety devices, and wiring connections. Verified proper operation of control board, circulator pump, and zone valves. Tested all safety switches and limit controls for proper functionality. Started boiler and monitored through complete heating cycle. Verified system reached proper operating
Successfully installed a new 20-gallon pressure tank and 40-60 PSI pressure switch to restore proper water pressure regulation to the residential plumbing system. The new pressure tank was integrated with the existing water supply lines using appropriate copper and brass fittings, ensuring secure connections throughout the assembly. The 40-60 pressure switch was mounted and calibrated to maintain optimal system pressure between the designated range, providing reliable automatic pump control and preventing pressure fluctuations that can damage plumbing fixtures and appliances.
Responded to service call for water pulsing and clicking noises at fixtures following recent iron filter installation. Diagnosed failed pressure tank as root cause of system malfunction. Provided estimate for pressure tank replacement to restore proper water pressure regulation and eliminate pulsing issues throughout the plumbing system.
Responded to service call for leaking water heater in residential basement. Upon inspection, found existing 40-gallon standard atmospheric vent water heater actively leaking from bottom of tank, indicating internal tank failure. Unit was still producing hot water but leak posed risk of water damage and complete failure. Evaluated installation location, existing venting configuration, and utility connections. Recommended replacement with 50-gallon power vent water heater to provide increased hot water capacity and improved venting efficiency. Documented existing equipment condition and installation area with photographs for replacement planning. Provided homeowner with replacement options and specifications for upgraded power vent system.
Responded to emergency water leak at exterior hose bib that would not shut off, requiring customer to shut off main water supply to the home. Upon inspection, diagnosed failed stem assembly causing continuous water flow from outdoor faucet. Replaced defective hose bib stem and handle assembly, restoring proper shut-off function and eliminating the leak.
Responded to a second opinion service call to evaluate air handler performance and suspected return air issues. Upon inspection, discovered the return air vent was completely disconnected from the air handler, causing the system to draw unconditioned air directly from the attic space. Properly reattached and secured the return air ductwork to restore proper airflow path. Performed diagnostic testing on the compressor using electrical testing equipment and confirmed compressor failure with abnormal amperage readings. Documented findings with photographic evidence of the disconnected ductwork and failed compressor diagnostics for customer records and future reference.
Responded to no cooling complaint on residential air conditioning unit approximately 5 years old. Upon arrival, observed condenser fan motor operating but compressor not running. Tested dual run capacitor and found compressor side reading significantly below manufacturer specifications. Temporarily connected known good capacitor to isolate component failure, but compressor still failed to start. Performed electrical diagnostics on compressor and confirmed internal short circuit within compressor windings. Explained findings to homeowner, including failed compressor requiring either compressor replacement or full system replacement. Homeowner requested time to obtain pricing estimates and evaluate repair versus replacement options before proceeding with work.
Responded to service call for malfunctioning garbage disposal unit. Upon inspection, determined existing disposal was inoperative and beyond repair. Identified improper drainage angle in undersink plumbing with back-pitched configuration causing water flow issues. Removed failed garbage disposal unit and installed new 3/4 HP replacement model. Completely reconfigured and reinstalled all undersink plumbing to correct drainage pitch and ensure proper water flow. Tested system operation and verified proper drainage function upon completion.
©2026 Hurlburt. All Rights Reserved.
Privacy Policy | Terms and
Conditions
This site is protected by reCAPTCHA and the Google Privacy Policy and Google Terms of Service apply.